![]() ![]() Make sure to set the IP address of this VM with a static IP on your network, as this will be your new PiHole DNS Server.Īlso, install OpenSSH during the install if you wish to SSH to Pi-Hole.Īfter installing Ubuntu, update the Ubuntu OS Installation MediaĪfter saving the VM settings, power on and run through a default setup of Ubuntu. On Installation Media, upload the Ubuntu ISO you downloaded earlier, or select it from your TrueNAS if you have already copied it to a share. You can take the defaults on Network Interfaces Network Interfaces and Installation Media I used a 12 GB Drive, which is probably overkill for this The minimum requirements were listed above, but I would add another vCPU core and some additional RAM VM CPU and MemoryĬreate new Disk Image and make sure to select AHCI as disk type. VM with a minimum 1 vCPU, 512MB vRAM, and 10GB Drive Deployment StepsĬreate a new VM in TrueNAS, using whatever values you prefer.īind should be the primary IP of your TrueNAS Operating System ![]() Deploying it as a VM is the next best thing. Unfortunately, running Pi-Hole on a jail isn’t really supported at this point, with previous attempts being abandoned by the community. If you don’t own one already, you’ll also need to add NanoPi M4 for $65 and up, a 12V power supply, an enclosure, and obivously the storage device(s).Having a dozen Raspberry Pi’s around the house is nice for random projects, but I would like to consolidate as much as I can into jails on FreeNAS/TrueNAS. This HAT will ease the design of NAS based on Rockchip RK3399 processor with up to four drive, and it won’t bread the bank as the 4x SATA HAT sells for $25 with heatsink, thermal pad, screws, metal standard, SATA I/F and power cable. Random reads and writes are much faster than eMMC flash modules and micro SD cards, but do not quite reach the performance of NVMe SSDs which can be connected to the company’s higher end NanoPC-T4 board. The company ran iozone to show the performance with one 750GB Crucial MX300 SSD. The company provides Ubuntu based Friendl圜ore 18.04 64-bit, FriendlyDesktop 18.04 64-bit, and Lubuntu 16.04 32bit with Linux 4.4, Uboot-2014.10 for NanoPi M4, and those images can be used with the M4 SATA HAT. 4-pin power connector with 12V and 5V output.12V DC input via power barrel jack or 4-pin header 2A needed for one 3.5″ hard drive or four 2.5″ hard drives 5A needed for four 3.5″ hard drives.Heat dissipation – 2x PCB nuts for mounting a heatsink on top of Marvell chipset 2-pin header for fan, PWM modulation for 12V output.Power key, unpopulated power key jumper.Expansion – NanoPi M4 40-pin header exposed.PCIe to SATA Chipset – Marvell 88SE9215 four-port 6Gbps SATA I/O controller.I feel like an odd choice at first glance, but it now makes complete sense, as the company has launched a 4x SATA HAT for NanoPi M4 board that leverages the header with PCIe 2x signals.Ĥx SATA HAT for NanoPi M4 key features and specifications: and exposes the 2-lane PCIe interface from the Rockchip processor not through a typical PCIe slot or mini PCIe slot, but instead through a 2.54mm pitch header. ![]() The SBC follows Raspberry Pi form factor, comes with 2 to 4 GB RAM, four USB 3.0 ports, Gigabit Etherent, HDMI 2.0, etc. NanoPi M4 is one of the many Rockchip RK3399 boards available on the market today. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |